SW-Motech Crash Bars & Engine Guards
This shelf covers everything SW-Motech makes to keep a bike upright, or at least in one piece, when it isn't. That's crash bars, engine guards, frame and axle sliders, lever guards, and the smaller reservoir and heel guards that go with them. All 523 carry a fitment tag. All but seventeen are matched to a specific make and model, from a BMW to a Royal Enfield. The rest are universal-fit. What differs between them is which part of the bike each one is built to take the hit for.
What each type actually protects
A Crash Bar is built to shield the engine, fairing and tank in a tip-over. It wraps around the outside of the engine, instead of tucking in tight against it. An Upper Crash Bar sits higher and further out, covering the tank and radiator specifically. SW-Motech sells the two separately, because they guard different zones of the same bike. Pick one without checking which zone it covers, and you can end up protecting the wrong part. Lower down, an Engine Guard sits under the engine and takes a rock strike or a kerb before the sump does. On some of the smaller bikes on this shelf, the same part is titled a Front Spoiler instead. Same job, different name. Neither word is one most riders search for. Frame Slider and Axle Slider kits do the same job further out again, at the fork, swingarm and axle ends. If the bike goes down, they let it slide instead of digging in. None of our 523 titles here use the words "bash plate", "skid plate" or "sump guard". If that's what you searched for, it's the Engine Guard or the Front Spoiler you want.
Built to protect the bike, not the rider
SW-Motech's own marketing copy for this range is worth reading closely. It never once claims to protect the person riding. Every sentence is about the bike: the engine, the fairing, the tank, the frame, the fork, the swingarm. That's simply what this hardware does, and it lines up with what UK riders say about it themselves. On the forums where people discuss fitting this kind of protection, the consistent line is that bars and sliders are for a tip-over or a low-speed drop. Nobody relies on them for a genuine high-speed crash. One claim comes up alongside that: a bar can transfer the impact into the frame instead of the engine case, making things worse. Riders raise this and argue about it. The one account behind it turned out to be a story about someone the poster knew, not anything closer to hand. Treat it as an open question among riders, not a settled fact either way.
One trade-off worth weighing
SW-Motech's own copy for the Crash Bar range makes a specific claim: the bars protect the engine and tank "without limiting lean angles". Riders fitting wider aftermarket bars from other makers have separately reported grounding them out in hard cornering. They're Renntec and R&G bars, not SW-Motech's. In one case, the rider was considering taking them off again. It's a real trade-off worth having in mind. A bar that covers more of the engine also sits further out towards the road. How much that matters depends on how the bike gets ridden.
What buyers say about fitting one of our own
On our own Honda CB500X crash bar (SBL.01.746.10000/B), verified UK buyers between 2021 and 2025 have rated the fit consistently well. They flagged the same two practical points more than once. The printed instructions are thin enough that it's worth watching a fitting video before you start. Have a set of larger Allen keys to hand too, along with the original spacers and screws from the bike, not just what comes in the box. One buyer's bar also arrived with a small area of powder coat already marked. Worth checking for before it goes on.
Before you order
Whether the fairing needs to come off to fit or service one varies by model. It's a real question that turns up online without a clean general answer. SW-Motech's own position on the engine guard family is that on some models, full access afterwards for routine work like an oil change "is not possible due to the design of the vehicle". Fitting one can trade off against how easy the bike is to service on certain models, not across the board. We also don't have a reliable answer, from any source, on whether a pannier or a luggage rack will foul a fitted crash bar on your particular combination. Worth checking before you order both. Nothing we found settles it either way.
Buying one
Every part on this shelf is for sale at 10% off RRP, with free UK delivery available. It's ordered against your bike's exact fitment, not a generic size. If you're not sure yet which of the wider SW-Motech range you need (carrier, luggage or protection), that's the page to start from. This one is for the smaller decision, once you already know it's a crash bar, an engine guard or a slider you're after.